C-1: Difference between revisions

From PigBoats.COM
(Added captions)
(Added photo and changed captions)
Line 1: Line 1:
[[File:C-Boat Header 1.jpg]]
[[File:C-Boat Header 1.jpg]]
[[File:C-1 Octopus launch.jpg|left|500px]]
<div style="text-align: justify;"><span style="color:#00008B">Octopus on the ways inside the covered building shed at the Fore River Shipbuilding Company yard in Quincy, MA. on her launch day, October 4, 1906. The covered building shed was a welcomed feature for the yard workers and for the building process. It allowed work to continue even in the harshest weather conditions. The two small platforms jutting out from the main deck on either side of the conning tower fairwater and braced to the hull were temporary in nature and intended to provide a little more deck space while surfaced. They were often taken down and stowed inside the superstructure when the boat got underway.
<small>Photo NH 44578 courtesy of the NHHC.</small>
[[File:Red bar sub.jpg]]


[[File:C-ways1.jpg|left|500px|]]
[[File:C-ways1.jpg|left|500px|]]
<div style="text-align: justify;"><span style="color:#00008B">Octopus on the building ways at Fore River Shipbuilding Co., Quincy, MA., probably just before her launch on October 4, 1906. Electric Boat's patented rotating bow cap for the muzzle doors of the torpedo tubes can clearly be seen here. The C-class had just two tubes. To open the muzzle ends of the tubes, the crew would manipulate controls inside the torpedo room that pushed the cap slightly forward to unseat the rubber gasket around each tube. A large handwheel inside the torpedo room would then be turned to rotate the cap so that the cutouts lined up with the tube muzzle ends. Once the tubes were shot, the crew would perform the opposite procedure: rotate the cap so that the cutouts in the cap were behind the upper and lower superstructure, then pull the lever back that seated the cap, creating a watertight seal on the muzzle end of the tube. EB would use the rotating cap feature on nearly all of its submarines up to the O-class of 1918. The two exceptions were the L and M-class. On the lower right on the bottom of the boat the port side bilge keel can be seen. This feature help to reduce rolling while on the surface.
Octopus hauled out on the marine railway at the Fore River yard, probably in late 1906 or early 1907 as she was being prepared for the 1907 Navy sponsored competitive trials against the [[Defender|'''Simon Lake XV''']], a design by inventor Simon Lake. Octopus has not yet been accepted by the Navy as she has not displaying the American flag. Electric Boat's patented rotating bow cap for the muzzle doors of the torpedo tubes can clearly be seen here. The C-class had just two tubes. To open the muzzle ends of the tubes, the crew would manipulate controls inside the torpedo room that pushed the cap slightly forward to unseat the rubber gasket around each tube. A large handwheel inside the torpedo room would then be turned to rotate the cap so that the cutouts lined up with the tube muzzle ends. Once the tubes were shot, the crew would perform the opposite procedure: rotate the cap so that the cutouts in the cap were behind the upper and lower superstructure, then pull the lever back that seated the cap, creating a watertight seal on the muzzle end of the tube. EB would use the rotating cap feature on nearly all of its submarines up to the O-class of 1918. The two exceptions were the L and M-class. On the lower right on the bottom of the boat the port side bilge keel can be seen. This feature help to reduce rolling while on the surface.


<small>U.S. Navy photo</small>
<small>U.S. Navy photo</small>
Line 9: Line 16:


[[File:C-1 on ways from stern.jpg|left|500px]]
[[File:C-1 on ways from stern.jpg|left|500px]]
Another view of Octopus on the building ways at the Fore River Shipbuilding Company, 1906. The Octopus was the first twin propeller submarine commissioned into the U.S. Navy, starting a trend that would last until 1953.
Another view of Octopus on the marine railway at the Fore River Shipbuilding Company, 1906-1907. The Octopus was the first twin propeller submarine commissioned into the U.S. Navy, starting a trend that would last until 1953.


<small>U.S. Navy photo</small>
<small>U.S. Navy photo</small>

Revision as of 16:46, 16 January 2024

Octopus on the ways inside the covered building shed at the Fore River Shipbuilding Company yard in Quincy, MA. on her launch day, October 4, 1906. The covered building shed was a welcomed feature for the yard workers and for the building process. It allowed work to continue even in the harshest weather conditions. The two small platforms jutting out from the main deck on either side of the conning tower fairwater and braced to the hull were temporary in nature and intended to provide a little more deck space while surfaced. They were often taken down and stowed inside the superstructure when the boat got underway.

Photo NH 44578 courtesy of the NHHC.

Octopus hauled out on the marine railway at the Fore River yard, probably in late 1906 or early 1907 as she was being prepared for the 1907 Navy sponsored competitive trials against the Simon Lake XV, a design by inventor Simon Lake. Octopus has not yet been accepted by the Navy as she has not displaying the American flag. Electric Boat's patented rotating bow cap for the muzzle doors of the torpedo tubes can clearly be seen here. The C-class had just two tubes. To open the muzzle ends of the tubes, the crew would manipulate controls inside the torpedo room that pushed the cap slightly forward to unseat the rubber gasket around each tube. A large handwheel inside the torpedo room would then be turned to rotate the cap so that the cutouts lined up with the tube muzzle ends. Once the tubes were shot, the crew would perform the opposite procedure: rotate the cap so that the cutouts in the cap were behind the upper and lower superstructure, then pull the lever back that seated the cap, creating a watertight seal on the muzzle end of the tube. EB would use the rotating cap feature on nearly all of its submarines up to the O-class of 1918. The two exceptions were the L and M-class. On the lower right on the bottom of the boat the port side bilge keel can be seen. This feature help to reduce rolling while on the surface.

U.S. Navy photo

Another view of Octopus on the marine railway at the Fore River Shipbuilding Company, 1906-1907. The Octopus was the first twin propeller submarine commissioned into the U.S. Navy, starting a trend that would last until 1953.

U.S. Navy photo

Octopus is shown here alongside a Fore River Shipbuilding dock in Quincy, MA., fall of 1907. Work to complete the Octopus for Navy acceptance is still ongoing, despite her having successfully passed the Navy demonstration the previous fall. The large ship next to her is the Steamship Everett, a collier built for the New England Coal & Coke Company that was delivered on October 19, 1907. This places the date of the photo to slightly before that date.

Photo in the private collection of Ric Hedman.

Octopus running at high speed, possibly in Narragansett Bay, Rhode Island, 1908-1909. This is likely Octopus' maximum speed of 11 knots. The men topside are only inches from the water and are in a precarious position if anything unexpected happens.

Photo from the collection of MMCM(SS) Rick Larson, USN (Ret.)

In another photo taken a few minutes after the one above, Octopus is seen entering a harbor, possibly Newport, R.I. or Norfolk, VA., 1908-1909. She is now at a much slower speed and her freeboard has increased slightly, making the men's position topside a little safer.

Photo from the collection of MMCM(SS) Rick Larson, USN (Ret.)

Octopus early in her career, probably 1906-1909, location unknown. Some small platforms have been temporarily rigged to the side of the superstructure fore and aft. Their purpose is unknown.

Photo in the private collection of Ric Hedman.

Octopus surfacing after a submerged run, possibly in Cape Cod Bay off Provincetown, MA., 1908-1910. She would still be running on the battery at this point, and would not start her engines until she was in full surface trim.

Photo in the private collection of Ric Hedman.

The battery compartment and torpedo tubes of the C-1, approximately 1912. The battery is an Edison Model 23-W, alkaline battery. It consists of 120 cells and had a capacity of 2550 Amps at a 3 hour discharge rate.

The wooden planks that cover the battery have been removed to show the individual plates and if you look closely you can see the small wood wedges (called cribbing) that hold the plates the designed distances from each other. When the decking is replaced it is screwed down and covered with a canvas that is shellacked down to make the deck waterproof. The shellack gives the decks a green color. With the deck in place the reload torpedoes and their storage skids would be in place on top of the deck.

The C-class submarines did not have individual watertight compartments. The entire boat, forward to aft, was one big compartment.

U.S. Navy photo

Detail from the above image. C-1 torpedo tubes showing the torpedo loading cable winches, sight glasses and associated piping and bow cap opening and closing hand wheel. A reload torpedo was positioned in front of the open tube door and a cable reeved through the pulley over the top center of each door from the winches seen above, and then to the rear of the torpedo.

On the outboard side of each winch drum are engaging handles to lock the drums onto a rotating shaft so you could only turn the selected winch drum and not the other. There is a long shaft running to what must have been a turning handle on the port side of the submarine but is obscured by anchor windlass motor gearing.

To the right of the starboard winch drum you can see an early interior communication sound powered phone system. It isn't clear if there are two handsets for listening but most likely you spoke into one and listened on the other. The cabling for these seems to come out of the large dial with the handsets on either side. It may be a way to dial specific stations in the submarine.

The valve handle in the top center is the "Forward Main Ballast Vent" opening and closing handle. When you dove someone had to open and close this valve to vent the tank of air.

The sight gauges between the tubes show how much water is in each tube. You want to make sure the tube is dry before opening, especially since the battery is just a few feet away.

U.S. Navy photo

Detail of the port torpedo loading winch cable drum at the image top. To the left is the handle that allows the drum to be selected for use while leaving the starboard drum disengaged. There is a similar handle on the starboard cable drum to select or deselect that winch. The large hand wheel is used to open and close the rotating bow cap that acts at the tube muzzle door. At the top is an clinometer to show angles of list or roll the sub is experiencing. The dial on the right is a mechanical indicator for what position the bow cap is in. Behind the bow cap wheel to the left is a horizontal handle that is used to "seat and unseat" the bow cap into either the open or closed positions after it has been rotated. It appears to be chained into position.

U.S. Navy photo

The control room of the C-1 looking aft. These are the electrical distribution panels used to control current flow from the generators to the battery, battery to the electric motors, and power distribution for assorted electrical equipment. You can see the starboard engine through the open doorway.

At the top right corner of the photo are control rods for the stern planes (right) and the rudder (left). The square panel below the rods, and a similar one on the left, are shaft rotation counters. They roll over like the odometer in a car. The large meters to the inside of the counters are volt meters. In the top left corner the large dark object looks to be a very big fan. Probably to cool the boat and prevent the buildup of gasoline fumes and or hydrogen gas from the batteries. The two panels handle the electrical to and from the battery and or the motors/generators for each shaft.

For a sense of scale, an average person today, standing in this space, could read the cards on the sloping desk above the center opening to the engine compartment. Headroom would probably be a scant 6 feet.

When considered from the perspective of the 21st century, this equipment seems primitive and incredibly unsafe. No internal bulkheads, open knife switches, gasoline engines, etc. But when this boat was built in 1906, it was the absolute state of the art and very advanced. We have come a long way since then.

U.S. Navy photo

This is the C-1's trim pump. It wa located in the aft port corner of the control room. It was used to pump sea water from and to the forward and after trim tanks, auxiliary tanks, and bilges so that a proper fore and aft trim (balance) could be maintained.

U.S. Navy photo

The C-1's engine room looking aft between the two Electric Boat/Craig gasoline engines. The 500 horsepower electrical motors for driving the submarine while submerged can be seen as two rounded objects just behind the engines. Fumes from the gasoline were a constant hazard to the crew. Even short-term exposure in an enclosed space can lead to headaches, nausea, and dizziness. It also causes a drunk-like stupor. In just a few years the Navy made a switch to diesel engines.

U.S. Navy photo

The C-1's engine room looking aft and to port over the top of the port clutch, above which may be the high-pressure air charging system.

U.S. Navy photo

C-1's engine room looking forward. The camera is just aft of the clutches and 500 horsepower main electrical motors. The view between the gasoline engines gives a look into the control room.

U.S. Navy photo

C-1 is shown here underway in what is likely the East River during the Naval Review at New York City, October 4, 1912. The ship in the background is likely the battleship USS Kearsarge (BB-5).

U.S. Navy photo

Return to the C-class page | Return to the Submarine Classes page

Page created by:
Ric Hedman & David Johnston
1999 - 2023 - PigBoats.COM©
Mountlake Terrace, WA, Norfolk, VA
webmaster at pigboats dot com